49848
2012 FEMA Risk Map Lidar: Merrimack River Watershed (Massachusetts, New Hampshire)
nh2012_fema_merrimackwatershed_m2516_metadata
Data Set
Published / External
49401
Lidar - partner (no harvest)
Project
Completed
2013-07-19
These data are the lidar points collected for FEMA Risk Mapping, Assessment, and Planning (Risk MAP) for the Merrimack River Watershed.
This area falls in portions of Hillsborough, Belknap, Merrimack, Rockingham and Strafford counties in New Hampshire and portions of
Essex, Middlesex and Worcester counties in Massachusetts.
Using a Leica ALS60 LiDAR system, a total of 268 flight lines of high density (Nominal Pulse Spacing of 1.0 m) were collected over the Merrimack
area which encompasses 1302 square miles. A total of 19 separate lifts were flown on November 11th, 12th and 13th and December 19th and 29th,
2011 and January 7th and 11th in 2012. One airborne global positioning system (GPS) base station was used to support the LiDAR data
acquisition: FIT B.
The data were received by the NOAA Office for Coastal Management from NH GRANIT. For data storage and Digital Coast provisioning purposes
the data were:
1. Converted from UTM Zone 19, meters, NAD83 to geographic coordinates.
2. Converted from NAVD88 (Geoid09), meters to ellipsoid heights, using Geoid09
Data available for download from the Digital Coast include the following classifications:
1. (Unclassified)
2. (Ground)
7. (Low Point Noise)
9. (Water)
10. (Ignored)
11. (Withheld for ASPRS Definition)
17. (USGS Overlap Default)
18. (USGS Overlap Ground)
Original contact information:
Contact Org: NH GRANIT
Phone: 603-862-1792
Email: granit@unh.edu
Provide high resolution terrain elevation and land cover elevation data. Terrain data is used to represent the topography of a watershed
and/or floodplain environment and to extract useful information for hydraulic and hydrologic models.
The FEMA Merrimack River HUC 8 LiDAR FY2010 report may be accessed at:
https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/2516/supplemental/Merrimack_River_HUC_8_01080202_Terrain_TSDN.pdf
A footprint of this data may be viewed in Google Earth at:
https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/2516/supplemental/2012_FEMA_Merrimack_River_Watershed_Lidar.kmz
Theme
ISO 19115 Topic Category
elevation
Theme
Bare Earth
Theme
Ground Control
Theme
Land Surface
Theme
Point Cloud
Office for Coastal Management
Charleston
SC
Data Set
Unknown
las
No warranty expressed or implied is made by FEMA regarding the utility of the data on any other system nor shall the act of distribution
constitute any such warranty. Any conclusions drawn from the analysis of this information are not the responsibility of FEMA, NH GRANIT,
the NOAA Office for Coastal Management or its partners.
Acknowledgement of FEMA would be appreciated in products derived from these data. This digital data is produced for the purposes of
updating/creating a DFIRM database. Ground control and quality control checkpoints were collected by CompassData, Inc. LiDAR was acquired
and processed by Photo Science, Inc. Quality Control testing was performed by CompassData, Inc. Quality Assurance testing was conducted
by Greenhorne & O'Mara, Inc. All firms were under contract to STARR, A Joint Venture which held the FEMA contract and task order for this work.
Data Steward
2013-07-19
Organization
NOAA Office for Coastal Management
NOAA/OCM
coastal.info@noaa.gov
2234 South Hobson Ave
Charleston
SC
29405-2413
(843) 740-1202
https://coast.noaa.gov
NOAA Office for Coastal Management Home Page
Online Resource
Distributor
2013-07-19
Organization
NOAA Office for Coastal Management
NOAA/OCM
coastal.info@noaa.gov
2234 South Hobson Ave
Charleston
SC
29405-2413
(843) 740-1202
https://coast.noaa.gov
NOAA Office for Coastal Management Home Page
Online Resource
Metadata Contact
2013-07-19
Organization
NOAA Office for Coastal Management
NOAA/OCM
coastal.info@noaa.gov
2234 South Hobson Ave
Charleston
SC
29405-2413
(843) 740-1202
https://coast.noaa.gov
NOAA Office for Coastal Management Home Page
Online Resource
Point of Contact
2013-07-19
Organization
NOAA Office for Coastal Management
NOAA/OCM
coastal.info@noaa.gov
2234 South Hobson Ave
Charleston
SC
29405-2413
(843) 740-1202
https://coast.noaa.gov
NOAA Office for Coastal Management Home Page
Online Resource
Ground Condition
-71.973079
-71.083734
42.53304
42.448337
Range
2011-11-11
2012-01-11
Yes
Unclassified
This data can be obtained on-line at the following URL:
https://coast.noaa.gov/dataviewer/#/lidar/search/where:ID=2516
This data set is dynamically generated based on user-specified parameters.
;
None
Users should be aware that temporal changes may have occurred since this data set was collected and some parts of this data may no
longer represent actual surface conditions. Users should not use this data for critical applications without a full awareness of its
limitations.
2013
https://coast.noaa.gov/dataviewer/#/lidar/search/where:ID=2516
2013-07-19
Organization
NOAA Office for Coastal Management
Customized Download
Create custom data files by choosing data area, product type, map projection, file format, datum, etc.
Zip
Zip
2013
https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/2516/index.html
2013-07-19
Organization
NOAA Office for Coastal Management
Bulk Download
Simple download of data files. The data is in orthometric heights and not the ellipsoid heights described in this metadata.
LAZ
LAS/LAZ - LASer
Zip
https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/2516/supplemental/2012_FEMA_Merrimack_River_Watershed_Lidar.kmz
Browse Graphic
Browse Graphic
kmz
This graphic shows the lidar coverage for the 2012 FEMA Merrimack River Watershed data set.
https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/2516/supplemental/Merrimack_River_HUC_8_01080202_Terrain_TSDN.pdf
Lidar collection report
Online Resource
pdf
Original report from the lidar contractor. It does not reflect any changes made after the original delivery to FEMA.
2017-03-20
Date that the source FGDC record was last modified.
2017-11-14
Converted from FGDC Content Standards for Digital Geospatial Metadata (version FGDC-STD-001-1998) using 'fgdc_to_inport_xml.pl' script. Contact Tyler Christensen (NOS) for details.
2018-02-08
Partial upload of Positional Accuracy fields only.
2018-03-13
Partial upload to move data access links to Distribution Info.
Deliverables were tested by for both vertical and horizontal accuracy. The vertical unit of the data file is in meters with 2-decimal
point precision.
Consolidated Vertical Accuracy (CVA) tested 24.3 cm at 95th percentile in: open terrain, forest terrain, and urban terrain. The Root Mean
Square Error (RMSE) for the elevation differences between GPS control points and lidar points is 11.4 m calculated with 76 supplemental
vertical accuracy (SVA) points.
Fundamental Vertical Accuracy (FVA) tested 14.0 cm at 95 percent confidence level in open terrain using RMSEz x 1.9600. The Root Mean Square
Error (RMSE) for the elevation differences between GPS control points and lidar points is 7.1 cm calculated with 20 FVA points.
The Merrimack_River_HUC_8_01080202_Terrain_TSDN.pdf may be accessed at:
https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/2516/supplemental/Merrimack_River_HUC_8_01080202_Terrain_TSDN.pdf
; Quantitative Value: 0.243 meters, Test that produced the value:
The Root Mean Square Error (RMSE) for the elevation differences between GPS control points and
lidar points in open terrain is 0.140 cm.
Survey data have been checked for completeness; points have been collected in correct vegetation units, and distributed
throughout the AOI. The terrain data have been checked for completeness against AOI polygons. No gaps as defined by FEMA Procedural Memo
No. 61 are known to exist within the dataset.
Survey data have been confirmed to be in proper units, coordinate systems and format. The terrain data have been
confirmed as complete LAS format data files. Header files are in proper LAS format with content as specified by FEMA Procedural Memo No. 61.
All_Returns
2012-01-01
Discrete
2012-09-14
Point Cloud (All Returns) LAS 1.2 point files named according to Merrimack_Tile_Index. | Type of Source Media: DIGITAL
Bare_Earth
2012-01-01
Discrete
2012-09-14
Bare Earth LAS point files named according to the Merrimack_Tile_Index. | Type of Source Media: DIGITAL
Merrimack HUC 8 1 meter DEM
2012-01-01
Discrete
2012-09-14
1 meter geotif file for Merrimack HUC 8 watershed project area. | Type of Source Media: DIGITAL
Merrimack HUC 8 2 meter DEM
2012-01-01
Discrete
2012-09-14
2 meter geotif file for Merrimack HUC 8 watershed project area. | Type of Source Media: DIGITAL
Merrimack HUC 8 tiled 1 meter DEMs
2012-01-01
Discrete
2012-09-14
1749 1 meter ERDAS Imagine files for Merrimack HUC 8 watershed project area. | Type of Source Media: DIGITAL
Merrimack Hydro Break Lines
2012-01-01
Discrete
2012-09-14
Merrimack Watershed 3D polyline breaklines. | Type of Source Media: DIGITAL
Merrimack TSDN
2012-01-01
Discrete
2012-09-14
TSDN for the acquisition, processing and product development of the LiDAR dataset. | Type of Source Media: DIGITAL
Merrimack_HUC8_2ft_Contours.gdb
2012-01-01
Discrete
2012-09-14
File geodatabase (v9.3) containing 2ft contour polyline feature classes for Merrimack HUC 8 based on HUC 12 boundaries. | Type of Source Media: DIGITAL
Merrimack_HUC8_ESRI_Terrain.gdb
2012-01-01
Discrete
2012-09-14
File geodatabase (v9.3.1) containing Merrimack HUC 8 ESRI Terrains. Includes bare earth multipoint (mass points),
hydro enforced breaklines (hard breakline), and project area (softclip) feature classes.
| Type of Source Media: DIGITAL
Region 1 Merrimack Testing Results FVA CVA
2012-01-01
Discrete
2012-09-14
Document contains QC test results for both FVA and CVA blind check point tests against
open area and bare earth surfaces generated from All Returns and Bare Earth (respectively) LAS points.
| Type of Source Media: DIGITAL
1
GPS based surveys were utilized to support both processing and testing of LiDAR data within FEMA designated Areas of Interest (AOIs). Geographically distinct ground points were surveyed using GPS technology throughout the AOI to provide support for three distinct tasks. Task 1 was to provide Vertical Ground Control to support the aerial acquisition and subsequent bare earth model processing. To accomplish this, survey-grade Trimble R-8 GPS receivers were used to collect a series of control points located on open areas, free of excessive or significant slope, and at least 5 meters away from any significant terrain break. Most if not all control points were collected at street/road intersections on bare level pavement.
Task 2 was to collect Fundamental Vertical Accuracy (FVA) checkpoints to evaluate the initial quality of the collected point cloud and to ensure that the collected data was satisfactory for further processing to meet FEMA specifications. The FVA points were collected in identical fashion to the Vertical Ground Control Points, but segregated from the point pool to ensure independent quality testing without prior knowledge of FVA locations by the aerial vendor. Task 3 was to collect Consolidated Vertical Accuracy CVA) checkpoints to allow vertical testing of the bare-earth processed LiDAR data in different classes of land cover, including: Open (pavement, open dirt, short grass), High Grass and Crops, Forest, Urban. CVA points were collected in similar fashion as Control and FVA points with emphasis on establishing point locations within the predominant land cover classes within each AOI or Functional AOI Group. In order to successfully collect the Forest land cover class, it was necessary to establish a Backsight and Initial Point with the R8 receiver, and then employ a Nikon Total Station to observe a retroreflective prism stationed under tree canopy. This was necessary due to the reduced GPS performance and degradation of signal under tree canopy. The R-8 receivers were equipped with cellular modems to receive real-time correction signals from the Keystone Precision Virtual Reference Station (VRS) network encompassing the Region 1 AOIs. Use of the VRS network allowed rapid collection times (~3 minutes/point) at 2.54 cm (1 inch) initial accuracy. All points collected were below the 8cm specification for testing 24cm, Highest category LiDAR data. To ensure valid in-field collections, an NGS monument with suitable vertical reporting was measured using the same equipment and procedures used for Control, FVA and CVA points on a daily basis. The measurement was compared to the NGS published values to ensure that the GPS collection schema was producing valid data and as a physical proof point of quality of collection.
2012-01-01T00:00:00
2
Those monument measurements are summarized in the Accuracy report included in the data deliverables. 20 FVA points are necessary to allow testing to CE95. 1 point out of 20 may fail vertical testing and still allow the entire dataset to meet 95% accuracy requirements. In similar fashion, 76 CVA points are necessary to test to CE95 as discussed above. 72 CVA points were collected with the intention at the outset that 4 of the collected FVAs would perform double, duty as Open-class CVA points, to total 76 CVAs.The following software packages and utilities were used to control the GPS receiver in the field during data collection, and then ingest and export the collected GPS data for all points: Trimble Survey Controller, Trimble Pathfinder Office. The following software utilities were used to translate the collected Latitude/Longitude Decimal Degree HAE GPS data for all points into Latitude/Longitude Degrees/Minutes/Seconds for checking the collected monument data against the published NGS Datasheet Lat/Long DMS values and into UTM NAD83 Northings/Eastings: U.S. Army Corps of Engineers CorpsCon, National Geodetic Survey Geoid09NAVD88. MSL values were determined using the most recent NGS-approved geoid model to generate geoid separation values for each Lat/Long coordinate pair. In this fashion, Orthometric heights were determined for each Control, FVA and CVA point by subtracting the generated Geoid Separation value from the Ellipsoidal Height (HAE) for publication and use as MSL NAVD88(09).
Using a Leica ALS60 LiDAR system, 268 flight lines of highest density (Nominal Pulse Spacing of 1.0m) were collected over the Merrimack area which encompasses 1302 square miles. Five (5) blocks (block or area is determined by the Base Station control locations, typically airports with ground control monuments available providing coverage within 18 miles of the base as possible) to cover in its entirety.
Area |Flight Lines |Lifts |Dates |System
CON |79 |7 |12/19-12/29 2011 |ALS60
ASH |64 |5 |1/7-1/11 2012 |ALS60
BED |31 |1 |1/11/2012 |ALS60
LCI |34 |2 |11/12-11/13 2011 |ALS60
AFN |48 |4 |11/12-11/13 2011 |ALS60
Cross Flights 12 Flight Lines...Lifts were combined with the acquisition of each area with both sensors
2012-01-01T00:00:00
3
Leica proprietary software was used in the post-processing of the airborne GPS and inertial data that is critical to the positioning and orientation of the sensor during all flights. Pairing the aircraft's raw trajectory data with the stationary GPS base station data, this software yields Leica IPAS TC (Inertial Positioning & Attitude Sensor Tightly Coupled) smoothed best estimate of trajectory (an SBET, in Leica's .sol file format) that is necessary for Leica's ALSPP post processing software to develop the resulting geo-referenced point cloud from the LiDAR missions. The point cloud is the mathematical three dimensional composite of all returns from all laser pulses as determined from the aerial mission. At this point this data is ready for analysis, classification, and filtering to generate a bare earth surface model in which the above-ground features are removed from the data set.
The point cloud was created using Leica Post Processor software. GeoCue was used in the creation of some of the files needed in downstream processing, as well as in the tiling of the dataset into more manageable file sizes. The TerraScan and TerraModeler software packages are then used for the automated data classification, manual cleanup, and bare earth generation from this data. Project specific macros were used to classify the ground and to remove the side overlap between parallel flight lines. All data was manually reviewed and any remaining artifacts removed using functionality provided by TerraScan and TerraModeler. QT Modeler was used as a final check of the bare earth dataset. GeoCue was then used to create the deliverable industry-standard LAS tiles for both the All Point Cloud Data and the Bare Earth. In-house software was then used to perform final statistical analysis of the classes in the LAS files.
Point Cloud data is manually reviewed and any remaining artifacts are removed using functionality provided within the TerraScan and TerraModeler software packages. Additional project specific macros are created and run within GeoCue/TerraScan to ensure correct LAS classification prior to project delivery. Final Classified LAS tiles are created within GeoCue to confirm correct LAS versioning and header information. In-house software is then used to check LAS header information and final LAS classification prior to delivery. LAS Class 2 is used to check the independent QC points against the Triangulated LiDAR surface.
2012-01-01T00:00:00
4
1-Convert LAS to Multipoint
2-Create Terrain
3-Convert Terrain to 1m Raster
4-Split 1m Raster into 1749 imagine files
5-Contour
Convert LAS to multipoint:
1. Create file geodatabase and create a feature dataset to store terrain information with appropriate projection and spatial domain.
2. Run LAS to multipoint tool in 3D analyst for the classified LAS files and select class 2 and 8.
3. Store results in file geodatabase feature dataset for terrain data.
Create Terrain
1. Create Terrain using multipoint as masspoints, hydro break lines as hard breakline and LiDAR coverage area as soft clip
2. Build Terrain and store in file geodatabase feature dataset for terrain data
Convert Terrain to 1m Raster
1. Run the Terrain to raster tool in 3D analyst
2. Float output data type, Linear as the method, CELLSIZE 1 as sampling distance, and Pyramid Level Resolution 0
3. Save results as a Geotiff dataset.
Split 1m Raster into tiles
1. Load 1m raster into ERDAS Imagine Mosaic pro tool
2. Split raster using LiDAR index
3. Save results as 1m imagine files
Create contours
1. Extract by mask from the 1m DEM using a HUC12 area. Save this raster as HUC12 Name 1m.
2. Focal Statistics using Extracted 1m DEM as input, Intermediate Focal Raster as Output, Neighborhood should be set to weighted kernel, and the statistic should be sum.
3. Create contours using focal stats raster as input, output polyline should be based on HUC12 name, Contour Interval of 2ft, Set base contour to DEM minimum z value
4. Check results and store in file geodatabase under the Analysis Contours feature dataset.
5. Focal Statistics using Extracted 1m DEM as input, Intermediate Focal Raster as Output, Neighborhood should be set to circle, and the statistic should be mean.
6. Create contours using focal stats raster as input, output polyline should be based on HUC12 name, Contour Interval of 2ft, Set base contour to DEM minimum z value
7. Check results and store in file geodatabase under the Cartographic Contours feature dataset.
2012-01-01T00:00:00
5
The NOAA Office for Coastal Management received elevation and intensity data las files in LAS v1.2 format. The data were in UTM Zone 19, meters, NAD83 coordinates and were vertically referenced to NAVD88 (Geoid09). The vertical units of the data were meters. OCM performed the following processing for data storage and Digital Coast provisioning purposes:
1. Data were filtered for outliers using the lastools tool, las2las
2. Data points that were withheld points, but were classified as 11, were converted to class 16, using the lastools tool, las2las
3. Data were converted from UTM Zone 19, meters, NAD83 to geographic coordinates.
4. Data were converted from NAVD88 (Geoid09) elevations, to ellipsoid elevations using Geoid09
5. Data were zipped to laz format
2013-07-01T00:00:00
Organization
NOAA Office for Coastal Management
NOAA/OCM
coastal.info@noaa.gov
2234 South Hobson Ave
Charleston
SC
29405-2413
(843) 740-1202
https://coast.noaa.gov
NOAA Office for Coastal Management Home Page
Online Resource
Bare_Earth
6
The withheld points were returned to class 11. The files were tagged as being in NAD83(2007) based on the date of collection, instead of a generic NAD83. The original report does not specify the NAD83 realization.
2022-08-29T00:00:00
Organization
NOAA Office for Coastal Management
NOAA/OCM
coastal.info@noaa.gov
2234 South Hobson Ave
Charleston
SC
29405-2413
(843) 740-1202
https://coast.noaa.gov
NOAA Office for Coastal Management Home Page
Online Resource
gov.noaa.nmfs.inport:49848
Anne Ball
2017-11-15T15:22:43
SysAdmin InPortAdmin
2023-10-17T16:12:16
2022-03-16
OCM Partners
OCMP
1002
Public
No
2022-03-16
1 Year
2023-03-16