Data Management Plan
DMP Template v2.0.1 (2015-01-01)Please provide the following information, and submit to the NOAA DM Plan Repository.
Reference to Master DM Plan (if applicable)
As stated in Section IV, Requirement 1.3, DM Plans may be hierarchical. If this DM Plan inherits provisions from a higher-level DM Plan already submitted to the Repository, then this more-specific Plan only needs to provide information that differs from what was provided in the Master DM Plan.
1. General Description of Data to be Managed
This image represents a 1 meter resolution backscatter mosaic of the St. John Shelf, US Virgin Islands. NOAA's NOS/NCCOS/CCMA Biogeography Team, in collaboration with NOAA vessel Nancy Foster and territory, federal, and private sector partners, acquired multibeam bathymetry data in the US Virgin Islands from March 18 2010 to April 06 2010. Data was acquired with a hull-mounted Reson 7125 Kongsberg Simrad EM 1002 multibeam echosounder (400 kHz) and processed by a NOAA contractor using CARIS HIPS software. Data has all correctors applied (attitude, sound velocity) and has been reduced to mean lower low water (MLLW) using final approved tides from NOAA COOPS. Data is in UTM zone 20 north, datum WGS84. The backscatter component of the bathymetry data were geometrically and radiometrically corrected using Hypack 2010 Geocoder software. Acoustic backscatter mosaics are ostensibly an important piece of information when characterizing surficial seafloor features and delineating benthic habitats. The project was conducted to meet IHO Order 1 and 2 accuracy standards, dependent on the project area and depth. All users should individually evaluate the suitability of this data according to their own needs and standards.
Notes: Only a maximum of 4000 characters will be included.
Notes: Data collection is considered ongoing if a time frame of type "Continuous" exists.
Notes: All time frames from all extent groups are included.
Notes: All geographic areas from all extent groups are included.
(e.g., digital numeric data, imagery, photographs, video, audio, database, tabular data, etc.)
(e.g., satellite, airplane, unmanned aerial system, radar, weather station, moored buoy, research vessel, autonomous underwater vehicle, animal tagging, manual surveys, enforcement activities, numerical model, etc.)
2. Point of Contact for this Data Management Plan (author or maintainer)
Notes: The name of the Person of the most recent Support Role of type "Metadata Contact" is used. The support role must be in effect.
Notes: The name of the Organization of the most recent Support Role of type "Metadata Contact" is used. This field is required if applicable.
3. Responsible Party for Data Management
Program Managers, or their designee, shall be responsible for assuring the proper management of the data produced by their Program. Please indicate the responsible party below.
Notes: The name of the Person of the most recent Support Role of type "Data Steward" is used. The support role must be in effect.
Programs must identify resources within their own budget for managing the data they produce.
5. Data Lineage and Quality
NOAA has issued Information Quality Guidelines for ensuring and maximizing the quality, objectivity, utility, and integrity of information which it disseminates.
(describe or provide URL of description):
- 2011-08-01 00:00:00 - For this project, the Chief Scientist was NOAA/NOS/NCCOS/CCMA's Tim Battista and the Lead Hydrographer was independent contractor Mike Stecher. Data was collected aboard the NOAA ship Nancy Foster from 3/18/10 to 4/06/10, as project number NF-10-03. Multibeam data was acquired in Simrad .hsx and .7k formats with hull-mounted Reson 7125 and Kongsberg Simrad EM 1002 multibeam echosounders (400 kHz). Simrad backscatter snippet collection was enabled. Line spacing for acquisition was three times the water depth, and data was retained out to 60 degrees from nadir, depending on project area. Heave, roll, pitch and heading correctors were collected using an Applanix POS/MV Model 320 inertial measurement unit (IMU) and associated Trimble GPS antennas. Sound velocity profiles were acquired with a Seabird Electronics SeaCat SBE19P CTD profiler and processed using Seabird Seaterm software. Positioning was obtained using Northstar 941X GPS receivers with differential correctors from U.S. Coast Guard CORS beacon Isabel, Puerto Rico. Data was reduced to Mean Lower-Low Water (MLLW) using final approved tides from NOAA COOPS, based on National Water Level Observation Network (NWLON) primary tide stations at Charlotte Amalie, VI (9751639) and Lime Tree Bay, VI (9751401). | Source Produced: NF-10-03 Raw Multibeam Data (Citation: NF-10-03 Raw Multibeam Data)
- 2011-08-01 00:00:00 - Raw SWMB data were converted and processed using CARIS HIPS v7.0 software, resulting in a CARIS HDCS format dataset with all correctors applied. Attitude and SWMB data was cleaned of fliers, and SWMB data was reviewed in subset mode by a NOAA contractor. | Source Produced: NF-10-03 HDCS Processed Multibeam Data (Citation: NF-10-03 Raw Multibeam Data)
- 2011-08-01 00:00:00 - Acoustic backscatter mosaics are ostensibly an important piece of information when characterizing surficial seafloor features and delineating benthic habitats. The multibeam backscatter data were corrected for geometric and radiometric distortions using Hypack 2010 Geocoder. In particular, the following corrections were applied where appropriate and when artifacts were evident: AVG Trend, TX Power and RX Gain, Area Correction, Spreading, Slant-Range and Extracted Beam Pattern. As no theoretical beam pattern for the Kongsberg Simrad 1002 system exists, it was extracted from a mapped area that was flat and had a relatively uniform (sandy) substrate. Individual lines were also truncated based on ping number and/or angle of incidence where appropriate. The final mosaics were exported as geotiffs, ASCII and XYB files (i.e., X,Y locations in WGS 1984 UTM Zone 20N and Backscatter values as measured in decibels dBs). | Source Produced: NF10_USVI_STJ_Shelf_Backscatter_1m.tif (Citation: NF-10-03 HDCS Processed Multibeam Data)
(describe or provide URL of description):
6. Data Documentation
The EDMC Data Documentation Procedural Directive requires that NOAA data be well documented, specifies the use of ISO 19115 and related standards for documentation of new data, and provides links to resources and tools for metadata creation and validation.
- 1.7. Data collection method(s)
- 4.1. Have resources for management of these data been identified?
- 4.2. Approximate percentage of the budget for these data devoted to data management
- 5.2. Quality control procedures employed
- 7.1. Do these data comply with the Data Access directive?
- 7.1.1. If data are not available or has limitations, has a Waiver been filed?
- 7.1.2. If there are limitations to data access, describe how data are protected
- 7.2. Name of organization of facility providing data access
- 7.2.1. If data hosting service is needed, please indicate
- 7.3. Data access methods or services offered
- 7.4. Approximate delay between data collection and dissemination
- 8.1. Actual or planned long-term data archive location
- 8.3. Approximate delay between data collection and submission to an archive facility
- 8.4. How will the data be protected from accidental or malicious modification or deletion prior to receipt by the archive?
(describe or provide URL of description):
7. Data Access
NAO 212-15 states that access to environmental data may only be restricted when distribution is explicitly limited by law, regulation, policy (such as those applicable to personally identifiable information or protected critical infrastructure information or proprietary trade information) or by security requirements. The EDMC Data Access Procedural Directive contains specific guidance, recommends the use of open-standard, interoperable, non-proprietary web services, provides information about resources and tools to enable data access, and includes a Waiver to be submitted to justify any approach other than full, unrestricted public access.
Please cite any use of this data.
Notes: The name of the Organization of the most recent Support Role of type "Distributor" is used. The support role must be in effect. This information is not required if an approved access waiver exists for this data.
Notes: This field is required if a Distributor has not been specified.
Notes: All URLs listed in the Distribution Info section will be included. This field is required if applicable.
Notes: This field is required if applicable.
8. Data Preservation and Protection
The NOAA Procedure for Scientific Records Appraisal and Archive Approval describes how to identify, appraise and decide what scientific records are to be preserved in a NOAA archive.
(Specify NCEI-MD, NCEI-CO, NCEI-NC, NCEI-MS, World Data Center (WDC) facility, Other, To Be Determined, Unable to Archive, or No Archiving Intended)
Notes: This field is required if archive location is World Data Center or Other.
Notes: This field is required if archive location is To Be Determined, Unable to Archive, or No Archiving Intended.
Notes: Physical Location Organization, City and State are required, or a Location Description is required.
Discuss data back-up, disaster recovery/contingency planning, and off-site data storage relevant to the data collection
9. Additional Line Office or Staff Office Questions
Line and Staff Offices may extend this template by inserting additional questions in this section.