Data Management Plan

DMP Template v2.0.1 (2015-01-01)

Please provide the following information, and submit to the NOAA DM Plan Repository.

Reference to Master DM Plan (if applicable)

As stated in Section IV, Requirement 1.3, DM Plans may be hierarchical. If this DM Plan inherits provisions from a higher-level DM Plan already submitted to the Repository, then this more-specific Plan only needs to provide information that differs from what was provided in the Master DM Plan.

URL of higher-level DM Plan (if any) as submitted to DM Plan Repository:

Always left blank

1. General Description of Data to be Managed

1.1. Name of the Data, data collection Project, or data-producing Program:

2014 USGS CMGP Lidar: Sandy Restoration (Delaware and Maryland)

Taken From: Item Identification | Title

1.2. Summary description of the data:

Geographic Extent: SANDY_Restoration_DE_MD_QL2 Area of Interest covers approximately 3.096 square miles. Lot #5 contains the full project area

Dataset Description: The SANDY_Restoration_DE_MD_QL2 project called for the Planning, Acquisition, processing and derivative products of LIDAR data to be collected at a nominal pulse spacing (NPS) of 0.7 meter. Project specifications are based on the U.S. Geological Survey National Geospatial Program Base LIDAR Specification, Version 1. The data was developed based on a horizontal projection/datum of UTM Zone 18 North, NAD83, meters and vertical datum of NAVD1988 (GEOID12A), meters. LiDAR data was delivered in RAW flight line swath format, processed to create Classified LAS 1.2 Files formatted to 3842 individual 1500m x 1500m tiles, and corresponding Intensity Images and Bare Earth DEMs tiled to the same 1500m x 1500m schema, and Breaklines in ESRI Shapefile format.

Ground Conditions: LiDAR was collected in Winter 2013 / Spring 2014, while no snow was on the ground and rivers were at or below normal levels. In order to post process the LiDAR data to meet task order specifications, Quantum Spatial established a total of 78 QA control points and 99 Land Cover control points that were used to calibrate the LIDAR to known ground locations established throughout the SANDY_Restoration_DE_MD_QL2 project area.

Taken From: Item Identification | Abstract
Notes: Only a maximum of 4000 characters will be included.

1.3. Is this a one-time data collection, or an ongoing series of measurements?

One-time data collection

Taken From: Extents / Time Frames | Time Frame Type
Notes: Data collection is considered ongoing if a time frame of type "Continuous" exists.

1.4. Actual or planned temporal coverage of the data:

2013-12-17 to 2014-04-06

Taken From: Extents | Time Frame - Start, Time Frame - End
Notes: All time frames from all extent groups are included.

1.5. Actual or planned geographic coverage of the data:

W: -76.425995, E: -75.039924, N: 39.853517, S: 38.101581

Taken From: Extents | Geographic Area Bounds, Geographic Area Description
Notes: All geographic areas from all extent groups are included.

1.6. Type(s) of data:
(e.g., digital numeric data, imagery, photographs, video, audio, database, tabular data, etc.)

Lidar point cloud

Taken From: Data Set Information | Data Presentation Form

1.7. Data collection method(s):
(e.g., satellite, airplane, unmanned aerial system, radar, weather station, moored buoy, research vessel, autonomous underwater vehicle, animal tagging, manual surveys, enforcement activities, numerical model, etc.)

No information found

Taken From: Acquisition Information | Instruments, Platforms

1.8. If data are from a NOAA Observing System of Record, indicate name of system:

Always left blank due to field exemption

1.8.1. If data are from another observing system, please specify:

Always left blank due to field exemption

2. Point of Contact for this Data Management Plan (author or maintainer)

2.1. Name:

NOAA Office for Coastal Management (NOAA/OCM)

Taken From: Support Roles (Metadata Contact) | Person
Notes: The name of the Person of the most recent Support Role of type "Metadata Contact" is used. The support role must be in effect.

2.2. Title:

Metadata Contact

Always listed as "Metadata Contact"

2.3. Affiliation or facility:

NOAA Office for Coastal Management (NOAA/OCM)

Taken From: Support Roles (Metadata Contact) | Organization
Notes: The name of the Organization of the most recent Support Role of type "Metadata Contact" is used. This field is required if applicable.

2.4. E-mail address:

coastal.info@noaa.gov

Notes: The email address is taken from the address listed for the Person assigned as the Metadata Contact in Support Roles.

2.5. Phone number:

(843) 740-1202

Notes: The phone number is taken from the number listed for the Person assigned as the Metadata Contact in Support Roles. If the phone number is missing or incorrect, please contact your Librarian to update the Person record.

3. Responsible Party for Data Management

Program Managers, or their designee, shall be responsible for assuring the proper management of the data produced by their Program. Please indicate the responsible party below.

3.1. Name:

No information found

Taken From: Support Roles (Data Steward) | Person
Notes: The name of the Person of the most recent Support Role of type "Data Steward" is used. The support role must be in effect.

3.2. Position Title:

Data Steward

Always listed as "Data Steward"

4. Resources

Programs must identify resources within their own budget for managing the data they produce.

4.1. Have resources for management of these data been identified?

Yes

Taken From: Data Management | Have resources for management of these data been identified?

4.2. Approximate percentage of the budget for these data devoted to data management (specify percentage or "unknown"):

Unknown

Taken From: Data Management | Approximate percentage of budget for these data devoted to data management

5. Data Lineage and Quality

NOAA has issued Information Quality Guidelines for ensuring and maximizing the quality, objectivity, utility, and integrity of information which it disseminates.

5.1. Processing workflow of the data from collection or acquisition to making it publicly accessible
(describe or provide URL of description):

Process Steps:

2014-01-01 00:00:00 - Classified LAS Processing: The bare earth surface is then manually reviewed to ensure correct classification on the Class 2 (Ground) points. After the bare-earth surface is finalized, it is then used to generate all hydro-breaklines through heads-up digitization. All ground (ASPRS Class 2) LiDAR data inside of the Lake Pond and Double Line Drain hydro flattening breaklines were then classified to water (ASPRS Class 9) using TerraScan macro functionality. A buffer of 0.7 meter was also used around each hydro-flattened feature to classify these ground (ASPRS Class 2) points to Ignored ground (ASPRS Class 10). All Lake Pond Island and Double Line Drain Island features were checked to ensure that the ground (ASPRS Class 2) points were reclassified to the correct classification after the automated classification was completed. All overlap data was processed through automated functionality provided by TerraScan to classify the overlapping flight line data to approved classes by USGS. The overlap data was classified to Class 17 (Overlap Default) and Class 18 (Overlap Ground). These classes were created through automated processes only and were not verified for classification accuracy. Due to software limitations within TerraScan, these classes were used to trip the withheld bit within various software packages. These processes were reviewed and accepted by USGS through numerous conference calls and pilot study areas. All data was manually reviewed and any remaining artifacts removed using functionality provided by TerraScan and TerraModeler. Global Mapper us used as a final check of the bare earth dataset. GeoCue was then used to create the deliverable industry-standard LAS files for both the All Point Cloud Data and the Bare Earth. Photo Science proprietary software was used to perform final statistical analysis of the classes in the LAS files, on a per tile level to verify final classification metrics and full LAS header information.
2015-11-01 00:00:00 - The NOAA Office for Coastal Management (OCM) received the topographic files in zip file format from USGS' ftp site. The data were received in UTM Zone 18N NAD83 coordinates (meters) and vertically referenced to NAVD88 using the Geoid12a model in meters. OCM performed the following processing for data storage and Digital Coast provisioning purposes: 1. LAS files were compressed to LAZ format with LASTools. 2. LAS files were removed of any duplicated points and extraneous points were reclassified to noise. 3. The LAS files were transformed to geographic (decimal degrees), ellipsoidal coordinates (meters) referenced to the Geoid12a model.

Taken From: Lineage | Lineage Statement, Process Steps (Process Date/Time, Source Citation Title, Description)

5.1.1. If data at different stages of the workflow, or products derived from these data, are subject to a separate data management plan, provide reference to other plan:

Always left blank

5.2. Quality control procedures employed
(describe or provide URL of description):

No information found

Taken From: Data Quality | Quality Control Procedures Employed

6. Data Documentation

The EDMC Data Documentation Procedural Directive requires that NOAA data be well documented, specifies the use of ISO 19115 and related standards for documentation of new data, and provides links to resources and tools for metadata creation and validation.

6.1. Does metadata comply with EDMC Data Documentation directive?

No

Notes: All required DMP fields must be populated and valid to comply with the directive.

6.1.1. If metadata are non-existent or non-compliant, please explain:

Missing/invalid information:

1.7. Data collection method(s)
3.1. Responsible Party for Data Management
5.2. Quality control procedures employed
7.1.1. If data are not available or has limitations, has a Waiver been filed?
7.4. Approximate delay between data collection and dissemination
8.3. Approximate delay between data collection and submission to an archive facility

Notes: Required DMP fields that are not populated or invalid are listed here.

6.2. Name of organization or facility providing metadata hosting:

NMFS Office of Science and Technology

Always listed as "NMFS Office of Science and Technology"

6.2.1. If service is needed for metadata hosting, please indicate:

Always left blank

6.3. URL of metadata folder or data catalog, if known:

https://www.fisheries.noaa.gov/inport/item/49662

Always listed as the URL to the InPort Data Set record

6.4. Process for producing and maintaining metadata
(describe or provide URL of description):

Metadata produced and maintained in accordance with the NOAA Data Documentation Procedural Directive: https://nosc.noaa.gov/EDMC/DAARWG/docs/EDMC_PD-Data_Documentation_v1.pdf

Always listed with the above statement

7. Data Access

NAO 212-15 states that access to environmental data may only be restricted when distribution is explicitly limited by law, regulation, policy (such as those applicable to personally identifiable information or protected critical infrastructure information or proprietary trade information) or by security requirements. The EDMC Data Access Procedural Directive contains specific guidance, recommends the use of open-standard, interoperable, non-proprietary web services, provides information about resources and tools to enable data access, and includes a Waiver to be submitted to justify any approach other than full, unrestricted public access.

7.1. Do these data comply with the Data Access directive?

Yes

Taken From: Data Management | Do these data comply with the Data Access directive?

7.1.1. If the data are not to be made available to the public at all, or with limitations, has a Waiver (Appendix A of Data Access directive) been filed?

No information found

Taken From: Data Management | Is access to the data limited based on an approved waiver?

7.1.2. If there are limitations to public data access, describe how data are protected from unauthorized access or disclosure:

None

Taken From: Access Info | Data Access Constraints

7.2. Name of organization of facility providing data access:

NOAA Office for Coastal Management (NOAA/OCM)

Taken From: Support Roles (Distributor) | Organization
Notes: The name of the Organization of the most recent Support Role of type "Distributor" is used. The support role must be in effect. This information is not required if an approved access waiver exists for this data.

7.2.1. If data hosting service is needed, please indicate:

Taken From: Data Management | If data hosting service is needed, please indicate
Notes: This field is required if a Distributor has not been specified.

7.2.2. URL of data access service, if known:

https://coast.noaa.gov/dataviewer/#/lidar/search/where:ID=4969
https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/4969/index.html

Taken From: Distribution Info | Download URL
Notes: All URLs listed in the Distribution Info section will be included. This field is required if applicable.

7.3. Data access methods or services offered:

Data is available online for bulk or custom downloads

Taken From: Access Info | Data Access Procedure

7.4. Approximate delay between data collection and dissemination:

No information found

Taken From: Data Management | Approximate delay between data collection and dissemination

7.4.1. If delay is longer than latency of automated processing, indicate under what authority data access is delayed:

Taken From: Data Management | If delay is longer than latency of automated processing, indicate under what authority data access is delayed
Notes: This field is required if applicable.

8. Data Preservation and Protection

The NOAA Procedure for Scientific Records Appraisal and Archive Approval describes how to identify, appraise and decide what scientific records are to be preserved in a NOAA archive.

8.1. Actual or planned long-term data archive location:
(Specify NCEI-MD, NCEI-CO, NCEI-NC, NCEI-MS, World Data Center (WDC) facility, Other, To Be Determined, Unable to Archive, or No Archiving Intended)

NCEI_CO

Taken From: Data Management | Actual or planned long-term data archive location

8.1.1. If World Data Center or Other, specify:

Taken From: Data Management | Actual or planned long-term data archive location
Notes: This field is required if archive location is World Data Center or Other.

8.1.2. If To Be Determined, Unable to Archive or No Archiving Intended, explain:

Taken From: Data Management | If To Be Determined, Unable to Archive or No Archiving Intended, explain
Notes: This field is required if archive location is To Be Determined, Unable to Archive, or No Archiving Intended.

8.2. Data storage facility prior to being sent to an archive facility (if any):

Office for Coastal Management - Charleston, SC

Taken From: Physical Location | Organization, City, State, Location Description
Notes: Physical Location Organization, City and State are required, or a Location Description is required.

8.3. Approximate delay between data collection and submission to an archive facility:

No information found

Taken From: Data Management | Approximate delay between data collection and submission to an archive facility

8.4. How will the data be protected from accidental or malicious modification or deletion prior to receipt by the archive?
Discuss data back-up, disaster recovery/contingency planning, and off-site data storage relevant to the data collection

Data is backed up to tape and to cloud storage.

Taken From: Data Management | How will the data be protected from accidental or malicious modification or deletion prior to receipt by the archive?

9. Additional Line Office or Staff Office Questions

Line and Staff Offices may extend this template by inserting additional questions in this section.

Always left blank