2012 USACE NCMP Topobathy Lidar: Mayport, FL

These files contain classified topo/bathy lidar data. Data are classified as 1 (valid non-ground topographic data), 2 (valid ground topographic data), and 29 (valid bathymetric data). Classes 1 and 2 are defined in accordance with the American Society for Photogrammetry and Remote Sensing (ASPRS) classification standards. These data were collected by the Coastal Zone Mapping and Imaging Lidar (CZMIL) system. CZMIL integrates a lidar sensor with simultaneous topographic and bathymetric capabilities, a digital camera and a hyperspectral imager on a single remote sensing platform for use in coastal mapping and charting activities. Native lidar data is not generally in a format accessible to most Geographic Information Systems (GIS). Specialized in-house and commercial software packages are used to process the native lidar data into 3-dimensional positions that can be imported into GIS software for visualization and further analysis. This project is a portion of a larger Florida acquisition from 2012 including Fort Myers and Egmont Key.

This data was provided to the NOAA Office for Coastal Management (OCM) for data distribution from the Data Access Viewer (DAV) and https. In addition to these lidar point data, the bare earth Digital Elevation Models (DEM) created from the lidar point data are also available. These data are available for custom download at the link provided in the URL section of this metadata record.

These data were collected as a part of the NCMP to depict the elevations above and below the water in the Florida coastal zone.

10351

A footprint of this data set may be viewed in Google Earth at:

https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/4993/supplemental/fl2012_usace_ncmp_mayport_m4993.kmz

LiDAR points in LAZ format (Classes 1,2,29)

none

Any conclusions drawn from the analysis of this information are not the responsibility of USACE, JALBTCX, NOAA, the Office for Coastal Management or its partners.

This data can be obtained on-line at the following URL:

https://coast.noaa.gov/dataviewer/#/lidar/search/where:ID=4993;

None

Users should be aware that temporal changes may have occurred since this data set was collected and some parts of this data may no longer represent actual surface conditions. Users should not use this data for critical applications without a full awareness of its limitations. These data depict the heights at the time of the survey and are only accurate for that time.

CZMIL topographic data - Compiled to meet 1 m horizontal accuracy at 95% confidence level. CZMIL bathymetric data - Compiled to meet 3.5 + 0.05d m horizontal accuracy at 95% confidence level, d is depth.

JALBTCX evaluates the horizontal accuracy of the final data coverage against available basemap imagery products. The final lidar point cloud is gridded according to procedures defined in the JALBTCX Standard Operating Guide and Appendices (SOGA). The grid products are then visually compared to basemap imagery products to verify the horizontal positions of large buildings and other urban features with the data coverage.

CZMIL topographic data - Compiled to meet 20 cm vertical accuracy at 95% confidence level. CZMIL bathymetric shallow FOV data - Compiled to meet SQRT((0.20^2) +((0.0075d)^2)) m vertical accuracy at 95% confidence level, d is depth. CZMIL bathymetric deep FOV data - Compiled to meet SQRT((0.30^2) +((0.013d)^2)) m vertical accuracy at 95% confidence level, d is depth.

JALBTCX evaluates the vertical accuracy of the final data coverage against traditional ground-truth data. Ground-truth data is acquired and utilized according to specifications outlined in the JALBTCX Standard Operating Guide and Appendices (SOGA) as well as the USGS Lidar Base Specification. The final lidar point cloud at every project ground-truth location is compared against ground-truth points in the 'bare_ground' class. Comparisons are performed in the QCoherent LP360 software package, and the final results are output to JALBTCX's Ground Truth Comparison Report.

This data set covers the spatial extent of topographic lidar data obtained during this survey.

During inspection and QC of the lidar point cloud, flightline to flightline elevation differences met the CZMIL sensor specifications.

The USACE collected, processed, and provided the data to the NOAA Office for Coastal Management (OCM). OCM received the data and processed it to be available for custom download from the Data Access Viewer (DAV) and for bulk download from https.