Data Management Plan
GUID: gov.noaa.nmfs.inport:50010 | Published / External
Data Management Plan
DMP Template v2.0.1 (2015-01-01)
Please provide the following information, and submit to the NOAA DM Plan Repository.Reference to Master DM Plan (if applicable)
As stated in Section IV, Requirement 1.3, DM Plans may be hierarchical. If this DM Plan inherits provisions from a higher-level DM Plan already submitted to the Repository, then this more-specific Plan only needs to provide information that differs from what was provided in the Master DM Plan.
1. General Description of Data to be Managed
This data set contains lidar point data (Geodetic Coordinates) from a strip of Southern California
coastline (including water, beach, cliffs, and top of cliffs) from Long Beach to the US/Mexico border. The data set was created
by combining data collected using an Optech Inc. Airborne Laser Terrain Mapper (ALTM) 1225 in combination with geodetic quality
Global Positioning System (GPS) airborne and ground-based receivers. The Bureau of Economic Geology, the University of Texas at
Austin owns and operates an ALTM 1225 system (serial number 99d118). The system was installed in a twin engine Partenavia P-68
(tail number N3832K) owned and operated by Aspen Helicopter, Inc. The lidar data set described by this document was collected on
24 and 25 March 2006; Julian Days 08306 and 08406 (see Lineage, Source_Information, Source_Contribution for pass information).
99d118 instrument settings for these flights were; laser pulse rate: 25kHz, scanner rate: 26Hz, scan angle: +/- 20deg, beam
divergence: narrow, altitude: 300-600m AGL, and ground speed: 95-120kts. Two GPS base stations were operating during each day
of the survey, Point Loma and San Onofre on 08306 and Seal Beach and San Onofre on 08406 (see Lineage, Source_Information,
and Source Contribution for coordinates). Data represented is all points including terrain, vegetation, and structures.
This data also contains returns from the water surface. No processing has been done to remove returns from terrain,
vegetation, structures or water surfaces.
Original contact information:
Contact Name: Julie Thomas/Randy Bucciarelli
Contact Org: SCBPS/CDIP, Scripps Institution of Oceanography
Title: Project Managers
Phone: 858-534-3032
Notes: Only a maximum of 4000 characters will be included.
Notes: Data collection is considered ongoing if a time frame of type "Continuous" exists.
Notes: All time frames from all extent groups are included.
Notes: All geographic areas from all extent groups are included.
(e.g., digital numeric data, imagery, photographs, video, audio, database, tabular data, etc.)
(e.g., satellite, airplane, unmanned aerial system, radar, weather station, moored buoy, research vessel, autonomous underwater vehicle, animal tagging, manual surveys, enforcement activities, numerical model, etc.)
2. Point of Contact for this Data Management Plan (author or maintainer)
Notes: The name of the Person of the most recent Support Role of type "Metadata Contact" is used. The support role must be in effect.
Notes: The name of the Organization of the most recent Support Role of type "Metadata Contact" is used. This field is required if applicable.
3. Responsible Party for Data Management
Program Managers, or their designee, shall be responsible for assuring the proper management of the data produced by their Program. Please indicate the responsible party below.
Notes: The name of the Person of the most recent Support Role of type "Data Steward" is used. The support role must be in effect.
4. Resources
Programs must identify resources within their own budget for managing the data they produce.
5. Data Lineage and Quality
NOAA has issued Information Quality Guidelines for ensuring and maximizing the quality, objectivity, utility, and integrity of information which it disseminates.
(describe or provide URL of description):
Process Steps:
- 2006-03-24 00:00:00 - GPS and XYZ-Point Data Processing Transfer raw ALTM 1225 flight data (laser ranges with associated scan angle information and IMU data), airborne GPS data collected at 1 Hz using Ashtech receiver, and ground-based GPS data collected at 1 Hz using Ashtech Z-12 receivers to processing computer. Generate decimated lidar point file from above three data sets using Optech's Realm 2.27 software. This is a 9-column ASCII data set with the following format: time tag; first pulse Easting, Northing, HAE; last pulse Easting, Northing, HAE; first pulse intensity; and last pulse intensity. View decimated lidar point file to check data coverage (i.e. sufficient overlap of flight lines and point spacing). Compute base station coordinates using National Geodetic Survey's PAGES-NT software. Compute aircraft trajectories from each base station GPS dataset using National Geodetic Survey's KINPOS software. Solutions for base stations coordinates and aircraft trajectories are in the International Terrestrial Reference Frame of 2000 (ITRF2000). A final aircraft trajectory was computed from a weighted average of the trajectories from the two base stations. Epoch-by-epoch weighting for the individual trajectories was inversely proportional to the baseline length (distance from base station) and solution RMS. Transformed trajectory solution from ITRF2000 to North American Datum of 1983 (NAD83) using the National Geodetic Survey's Horizontal Time Dependent Positioning software (http://www.ngs.noaa.gov/TOOLS/Htdp/Htdp.html). Input NAD83 trajectories and aircraft inertial measurement unit data into Applanix's POSProc version 2.1.4 to compute an optimal 50Hz inertial navigation solution (INS) and smoothed best estimate of trajectory (SBET). Substitute the INS and SBET into Realm 2.27. Generate a set of initial lidar instrument calibration parameters (pitch, roll, scale, and elevation bias) for each lidar flight, then incrementally improve parameters by iteratively comparing a subset of the lidar output to the GPS kinematic ground control. Once the instrument calibration parameters are sufficiently accurate, create the complete lidar point file (9-column ASCII file) for the entire survey area in UTM Zone 11 with elevations being heights above the GRS-80 reference ellipsoid (HAE). The output format from REALM 2.27 was a 9-column ASCII file containing: the second in the GPS week, easting, northing and HAE of the first lidar return, the easting, northing and HAE of the last lidar return, and the laser backscatter intensity of the first and last returns. Using the GEOID99 geoid model, heights above the GRS80 ellipsoid were converted to orthometric heights with respect to the North American Vertical Datum of 1988 (NAVD88). Parse the 9-column lidar point file into 3.75-minute quarter-quadrangle components. Convert UTM Easting and Northing to geodetic latitude and longitude with respect to the GRS80 ellipsoid. The conversion was computed using the TMGEOD and TCONPC fortran subroutines written by T. Vincenty (NGS). Each record contains 9 columns of data: time tag (seconds in the GPS week), first return Latitude,first return Longitude, first return NAVD88, last return Latitude, last return Longitude, last return NAVD88, first return intensity, and last return intensity. In some cases either the first or last return values may be missing (5 columns). Latitude and longitude are in decimal degrees with nine significant digits to retain the 0.01m resolution of the UTM coordinates. West longitude is negative and north latitude is positive. The UTM quarter-quad files were re-organized into latitude delineated files. UTM quarter-quads files that were delineated by the same upper and lower latitude bounds were concatenated. The lat-long files were named by the month-year of the survey (e.g. mar06) and the lower latitude bounding the quarter-quad. Processing occurred 20060324-20060726.
- 2003-04-18 00:00:00 - Created initial metadata
- 2007-07-24 00:00:00 - The NOAA Office for Coastal Management (OCM) received files in ASCII format. The files contained LiDAR intensity and elevation measurements. OCM performed the following processing on the data to make it available within the LiDAR Data Retrieval Tool (LDART) 1. Data returned to ellipsoid heights from NAVD88, using GEOID99. 2. Data converted to LAS format. 3. The LAS data were sorted by latitude and the headers were updated.
(describe or provide URL of description):
6. Data Documentation
The EDMC Data Documentation Procedural Directive requires that NOAA data be well documented, specifies the use of ISO 19115 and related standards for documentation of new data, and provides links to resources and tools for metadata creation and validation.
Missing/invalid information:
- 1.6. Type(s) of data
- 1.7. Data collection method(s)
- 3.1. Responsible Party for Data Management
- 4.1. Have resources for management of these data been identified?
- 4.2. Approximate percentage of the budget for these data devoted to data management
- 5.2. Quality control procedures employed
- 7.1. Do these data comply with the Data Access directive?
- 7.1.1. If data are not available or has limitations, has a Waiver been filed?
- 7.1.2. If there are limitations to data access, describe how data are protected
- 7.4. Approximate delay between data collection and dissemination
- 8.1. Actual or planned long-term data archive location
- 8.3. Approximate delay between data collection and submission to an archive facility
- 8.4. How will the data be protected from accidental or malicious modification or deletion prior to receipt by the archive?
(describe or provide URL of description):
7. Data Access
NAO 212-15 states that access to environmental data may only be restricted when distribution is explicitly limited by law, regulation, policy (such as those applicable to personally identifiable information or protected critical infrastructure information or proprietary trade information) or by security requirements. The EDMC Data Access Procedural Directive contains specific guidance, recommends the use of open-standard, interoperable, non-proprietary web services, provides information about resources and tools to enable data access, and includes a Waiver to be submitted to justify any approach other than full, unrestricted public access.
none
Notes: The name of the Organization of the most recent Support Role of type "Distributor" is used. The support role must be in effect. This information is not required if an approved access waiver exists for this data.
Notes: This field is required if a Distributor has not been specified.
https://noaa-nos-coastal-lidar-pds.s3.amazonaws.com/laz/geoid18/54/index.html
Notes: All URLs listed in the Distribution Info section will be included. This field is required if applicable.
This data can be obtained on-line at the following URL: https://coast.noaa.gov/dataviewer
;
Notes: This field is required if applicable.
8. Data Preservation and Protection
The NOAA Procedure for Scientific Records Appraisal and Archive Approval describes how to identify, appraise and decide what scientific records are to be preserved in a NOAA archive.
(Specify NCEI-MD, NCEI-CO, NCEI-NC, NCEI-MS, World Data Center (WDC) facility, Other, To Be Determined, Unable to Archive, or No Archiving Intended)
Notes: This field is required if archive location is World Data Center or Other.
Notes: This field is required if archive location is To Be Determined, Unable to Archive, or No Archiving Intended.
Notes: Physical Location Organization, City and State are required, or a Location Description is required.
Discuss data back-up, disaster recovery/contingency planning, and off-site data storage relevant to the data collection
9. Additional Line Office or Staff Office Questions
Line and Staff Offices may extend this template by inserting additional questions in this section.