2019 - 2020 USGS Lidar: Central Georgia

Block 6

Dates of collection for Block 6.

Block 2

Dates of collection for Block 2.

Block 5

Dates of collection for Block 5.

Block 4

Dates of collection for Block 4.

Block 3

Dates of collection for Block 3.

Block 1

Dates of collection for Block 1.

Create custom data files by choosing data area, product type, map projection, file format, datum, etc. A new metadata will be produced to reflect your request using this record as a base. Change to an orthometric vertical datum is one of the many options.

Bulk download of data files from Blocks 4, 5,and 6 in LAZ format, Albers Equal Area NAD83(2011) meters coordinates and orthometric heights in meters.

Bulk download of data files from Blocks 1, 2, and 3 in LAZ format, Albers Equal Area NAD83(2011) meters coordinates and orthometric heights in meters.

The Data Access Viewer (DAV) allows a user to search for and download elevation, imagery, and land cover data for the coastal U.S. and its territories. The data, hosted by the NOAA Office for Coastal Management, can be customized and requested for free download through a checkout interface. An email provides a link to the customized data, while the original data set is available through a link within the viewer.

Link to the USGS Project Report that provides information about the project, vertical accuracy results, and the point classes and sensors used.

Link to the reports, breaklines, metadata, and spatial metadata.

Link to the lidar report for Block 1 (Work Unit 183176).

Link to the lidar report for Block 5 (Work Unit 231249).

Link to the lidar report for Block 2 (Work Unit 183296).

Link to the lidar report for Block 3 (Work Unit 217457).

Link to the lidar report for Block 4 (Work Unit 223562).

Link to the lidar report for Block 6 (Work Unit 300006).

Entwine Point Tile (EPT) is a simple and flexible octree-based storage format for point cloud data. The data is organized in such a way that the data can be reasonably streamed over the internet, pulling only the points you need. EPT files can be queried to return a subset of the points that give you a representation of the area. As you zoom further in, you are requesting higher and higher densities. A dataset in EPT will contain a lot of files, however, the ept.json file describes all the rest. The EPT file can be used in Potree and QGIS to view the point cloud.

Entwine Point Tile (EPT) is a simple and flexible octree-based storage format for point cloud data. The data is organized in such a way that the data can be reasonably streamed over the internet, pulling only the points you need. EPT files can be queried to return a subset of the points that give you a representation of the area. As you zoom further in, you are requesting higher and higher densities. A dataset in EPT will contain a lot of files, however, the ept.json file describes all the rest. The EPT file can be used in Potree and QGIS to view the point cloud.

Entwine Point Tile (EPT) is a simple and flexible octree-based storage format for point cloud data. The data is organized in such a way that the data can be reasonably streamed over the internet, pulling only the points you need. EPT files can be queried to return a subset of the points that give you a representation of the area. As you zoom further in, you are requesting higher and higher densities. A dataset in EPT will contain a lot of files, however, the ept.json file describes all the rest. The EPT file can be used in Potree and QGIS to view the point cloud.

Entwine Point Tile (EPT) is a simple and flexible octree-based storage format for point cloud data. The data is organized in such a way that the data can be reasonably streamed over the internet, pulling only the points you need. EPT files can be queried to return a subset of the points that give you a representation of the area. As you zoom further in, you are requesting higher and higher densities. A dataset in EPT will contain a lot of files, however, the ept.json file describes all the rest. The EPT file can be used in Potree and QGIS to view the point cloud.

Entwine Point Tile (EPT) is a simple and flexible octree-based storage format for point cloud data. The data is organized in such a way that the data can be reasonably streamed over the internet, pulling only the points you need. EPT files can be queried to return a subset of the points that give you a representation of the area. As you zoom further in, you are requesting higher and higher densities. A dataset in EPT will contain a lot of files, however, the ept.json file describes all the rest. The EPT file can be used in Potree and QGIS to view the point cloud.

Entwine Point Tile (EPT) is a simple and flexible octree-based storage format for point cloud data. The data is organized in such a way that the data can be reasonably streamed over the internet, pulling only the points you need. EPT files can be queried to return a subset of the points that give you a representation of the area. As you zoom further in, you are requesting higher and higher densities. A dataset in EPT will contain a lot of files, however, the ept.json file describes all the rest. The EPT file can be used in Potree and QGIS to view the point cloud.

Link to view the point cloud, using the Entwine Point Tile (EPT) format, in the 3D Potree viewer.

Aircraft and Sensor Information and Flight Plan Execution -- Atlantic operated a PACDV (N750DV) outfitted with an Optech Galaxy Prime LiDAR system during the collection of the project area. Atlantic acquired passes of the AOI as a series of perpendicular and/or adjacent flight-lines executed in flight missions conducted between December 2019 and June 2020. Onboard differential Global Navigation Satellite System (GNSS) unit(s) recorded sample aircraft positions at 2 hertz (Hz) or more frequency. LiDAR data was only acquired when a minimum of six (6) satellites were in view. Twenty-three (23) Continuously Operating Reference Stations (CORS) were used to control the LiDAR acquisition for the defined project area.

Ground Control Survey -- Ground survey points were collected in support of this project, including LiDAR Control Points (LCP), Non-vegetated Vertical Accuracy (NVA) and Vegetated Vertical Accuracy (VVA).

Point cloud data accuracy was tested against a Triangulated Irregular Network (TIN) constructed from LiDAR points in clear and open areas. A clear and open area can be characterized with respect to topographic and ground cover variation such that a minimum of five (5) times the Nominal Pulse Spacing (NPS) exists with less than 1/3 of the RMSEZ deviation from a low-slope plane. Slopes that exceed ten (10) percent were avoided.

Each land cover type representing ten (10) percent or more of the total project area were tested and reported with a VVA. In land cover categories other than dense urban areas, the tested points did not have obstructions forty-five (45) degrees above the horizon to ensure a satisfactory TIN surface. The VVA value is provided as a target. It is understood that in areas of dense vegetation, swamps, or extremely difficult terrain, this value may be exceeded.

The NVA value is a requirement that must be met, regardless of any allowed “busts” in the VVA(s) for individual land cover types within the project. Checkpoints for each assessment (NVA and VVA) are required to be well-distributed throughout the land cover type, for the entire project area.

LiDAR Point Cloud Generation -- Atlantic used Leica software products to download the IPAS ABGNSS/IMU data and raw laser scan files from the airborne system. Waypoint Inertial Explorer is used to extract the raw IPAS ABGNSS/IMU data, which is further processed in combination with controlled base stations to provide the final Smoothed Best Estimate Trajectory (SBET) for each mission. The SBETs are combined with the raw laser scan files to export the LiDAR ASCII Standard (*.las) formatted swath point clouds.

LiDAR Calibration -- Using a combination of GeoCue, TerraScan and TerraMatch; overlapping swath point clouds are corrected for any orientation or linear deviations to obtain the best fit swath-to-swath calibration. Relative calibration was evaluated using advanced plane-matching analysis and parameter corrections derived. This process was repeated interactively until residual errors between overlapping swaths, across all project missions, was reduced to ≤2cm. A final analysis of the calibrated lidar is performed using a TerraMatch tie line report for an overall statistical model of the project area. Individual control point assessments for this project can be found in Section VI of the report.

Upon completion of the data calibration, a complete set of elevation difference intensity rasters (dZ Orthos) are produced. A user-defined color ramp is applied depicting the offsets between overlapping swaths based on project specifications. The dZ orthos provide an opportunity to review the data calibration in a qualitative manner. Atlantic assigns green to all offset values that fall below the required RMSDz requirement of the project. A yellow color is assigned for offsets that fall between the RMSDz value and 1.5x of that value. Finally, red values are assigned to all values that fall beyond 1.5x of the RMSDz requirements of the project.

LiDAR Classification -- Multiple automated filtering routines are applied to the calibrated LiDAR point cloud identifying and extracting bare-earth and above ground features. GeoCue, TerraScan, and TerraModeler software was used for the initial batch processing, visual inspection and any manual editing of the LiDAR point clouds. Atlantic utilized collected breakline data to perform classification for class 9 (Water).

Original point clouds in LAS/LAZ format were restructured as Entwine Point Tiles and stored on Amazon Web Services. The data were re-projected horizontally to WGS84 web mercator (EPSG 3857) and no changes were made to the vertical elevations in NAVD88 (GEOID12B).

The NOAA Office for Coastal Management (OCM) created references to the Entwine Point Tile (EPT) files that were ingested into the NOAA Digital Coast Data Access Viewer (DAV). No changes were made to the data. The DAV will access the point cloud as it resides on Amazon Web Services (AWS) under the usgs-lidar-public container.

These are the AWS URLs being accessed:

https://s3-us-west-2.amazonaws.com/usgs-lidar-public/GA_Central_1_2018/ept.json

https://s3-us-west-2.amazonaws.com/usgs-lidar-public/GA_Central_2_2018/ept.json

https://s3-us-west-2.amazonaws.com/usgs-lidar-public/GA_Central_3_2018/ept.json

https://s3-us-west-2.amazonaws.com/usgs-lidar-public/GA_Central_4_2018/ept.json

https://s3-us-west-2.amazonaws.com/usgs-lidar-public/GA_Central_5_2018/ept.json

https://s3-us-west-2.amazonaws.com/usgs-lidar-public/GA_Central_6_2018/ept.json